数字钟课程设计_课程设计数字钟

数字钟课程设计由刀豆文库小编整理，希望给你工作、学习、生活带来方便，猜你可能喜欢“课程设计数字钟”。

ORG 0000H SJMP ONE ORG 0003H LJMP ELEVEN ORG 000BH LJMP NINE ORG 001BH LJMP TEN ONE:LED12 EQU 30H;数码管12显示缓存 LED34 EQU 31H;数码管34显示缓存 LED56 EQU 32H;数码管56显示缓存

COUNT EQU 33H;定时器T0（用来走时）计数值存储器（计数中断20次到1秒）COUNTS EQU 34H;定时器T1（用来预置）计数值存储器（计数中断15次到预置值加一）HOUR EQU 40H;以下为时间，日期，闹铃时间，生日的存储地址 MIN EQU 41H SECOND EQU 22H YEAR EQU 50H MONTH EQU 23H DAY EQU 52H RH EQU 60H;闹铃小时 RM EQU 61H;闹铃分 RE EQU 62H;闹铃使能 BM EQU 71H;生日－月份 BD EQU 72H;生日－天 MOV LED12,#0 MOV LED34,#0 MOV LED56,#0 MOV COUNT,#0 MOV COUNTS,#0 MOV HOUR,#0 MOV MIN,#0 MOV SECOND,#0 MOV YEAR,#0 MOV MONTH,#1 MOV DAY,#1 MOV RH,#0 MOV RM,#0 MOV RE,#0 MOV BM,#6 MOV BD,#1 BS BIT 00H;birthday symbol生日标志（到生日那天就为1）

SS BIT 01H;set symbol预置信号（按下中断预置为1，便开始闪烁和预置）GS BIT 02H;glisten symbol闪烁标志 FC BIT 03H;frequency control频率控制 NB BIT 04H;neglect bitrhday symbol 忽略生日标志 CLR BS CLR SS CLR GS CLR FC CLR NB SETB 05H;生日显示有效标志位 MOV IP,#02H;中断优先级：T0>INT0>T1 MOV TMOD,#11H MOV IE,#8BH SETB IT0 MOV TH0,#3CH;50ms MOV TL0,#0B0H SETB TR0 MOV R1,#50;显示延时用 MOV R0,#0;显示延时用

;************************************************************** TWO检测开关号 TWO:MOV P0,#0FFH JB P0.5,TWO1 MOV RE,#0A0H;0A0表示闹铃无效，送0A0是为了方便将使能查表显示，表中第A项为“-” SJMP TWO2 TWO1:MOV RE,#0A1H TWO2:JB P0.0,TWO4 JB P0.1,TWO3 MOV LED12,HOUR MOV LED34,MIN MOV LED56,SECOND SJMP THREE TWO3:MOV LED12,YEAR MOV LED34,MONTH MOV LED56,DAY SJMP THREE TWO4:JB P0.1,TWO5 MOV LED12,RH MOV LED34,RM MOV LED56,RE SJMP THREE TWO5:MOV LED12,BM MOV LED34,BD MOV LED56,#0BCH SJMP THREE;************************************** THREE显示主程序（同时包含了闹铃，预置闪烁，闹铃功能）THREE:MOV P1,#0 MOV P0,#0FFH MOV DPTR,#TAB3 JNB SS,THREEB;判断预置信号是否有效，预置有效则转入判断闪烁显示模块，否则转入正常显示模块

SJMP THREEA THREEB:LJMP THREE11;THREE11是正常显示并判断整点报时及闹铃模块

THREEA:JNB P0.3,THREE1;开始是判断闪烁显示，这句判断是否预置分/月/生日的日/闹铃分

JNB GS,THREE1;是否闪烁？

LCALL TWELVE;闪烁则调用延时不显示LED34 SJMP THREE4 THREE1:MOV A,LED34 ANL A,#0FH MOVC A,@A+DPTR MOV P2,A THREE2:SETB P1.3 NOP DJNZ R0,THREE2 CLR P1.3 MOV A,LED34 SWAP A ANL A,#0FH MOVC A,@A+DPTR MOV P2,A THREE3:SETB P1.2 NOP DJNZ R0,THREE3 CLR P1.2 JNB P0.2,THREE4;判断是否预置小时/年/生日月/闹铃的小时 JNB GS,THREE4;是否显示小时/年/生日月/闹铃的小时 LCALL TWELVE SJMP THREE7 THREE4:MOV A,LED12 ANL A,#0FH MOVC A,@A+DPTR MOV P2,A THREE5:SETB P1.1 NOP DJNZ R0,THREE5 CLR P1.1 MOV A,LED12 SWAP A ANL A,#0FH MOVC A,@A+DPTR MOV P2,A THREE6:SETB P1.0 NOP DJNZ R0,THREE6 CLR P1.0 JB P0.0,THREE7;数码管56只有在显示日期的天时才有预置闪烁功能，其余三项都不需要判断闪烁 JNB P0.1,THREE7 JB P0.3,THREE7 JNB P0.4,THREE7 JNB GS,THREE7 LCALL TWELVE SJMP THREE10 THREE7:MOV A,LED56 ANL A,#0FH MOVC A,@A+DPTR MOV P2,A THREE8:SETB P1.5 NOP DJNZ R0,THREE8 CLR P1.5 MOV A,LED56 SWAP A ANL A,#0FH MOVC A,@A+DPTR MOV P2,A THREE9:SETB P1.4 NOP DJNZ R0,THREE9 CLR P1.4 THREE10:DJNZ R1,TWOA SJMP TWOB TWOA:LJMP TWO TWOB:MOV R1,#50;判断闪烁一次是否完成 CPL GS;取反闪烁标志，用于控制闪烁的亮和灭 LJMP TWO;一轮显示完后再判断开关号;**************************正常显示

THREE11:LCALL EIGHT;判断是否取反P1.6即输出闹铃或整点报时，以下每次显示都要调用一次

JB NB,THREE12;如果是在整点报时状态就不显示生日提醒，报时过后显示提醒 JNB BS,THREE12 SJMP SEVEN;跳到生日提醒程序

THREE12:CLR NB;开始正常显示时间及判断闹铃输出 MOV A,LED34 ANL A,#0FH MOVC A,@A+DPTR MOV P2,A THREE13:SETB P1.3 NOP DJNZ R0,THREE13 CLR P1.3 MOV A,LED34 SWAP A ANL A,#0FH MOVC A,@A+DPTR MOV P2,A THREE14:SETB P1.2 NOP DJNZ R0,THREE14 CLR P1.2 LCALL EIGHT MOV A,LED12 ANL A,#0FH MOVC A,@A+DPTR MOV P2,A THREE15:SETB P1.1 NOP DJNZ R0,THREE15 CLR P1.1 MOV A,LED12 SWAP A ANL A,#0FH MOVC A,@A+DPTR MOV P2,A THREE16:SETB P1.0 NOP DJNZ R0,THREE16 CLR P1.0 LCALL EIGHT MOV A,LED56 ANL A,#0FH MOVC A,@A+DPTR MOV P2,A THREE17:SETB P1.5 NOP DJNZ R0,THREE17 CLR P1.5 MOV A,LED56 SWAP A ANL A,#0FH MOVC A,@A+DPTR MOV P2,A THREE18:SETB P1.4 NOP DJNZ R0,THREE18 CLR P1.4 LJMP TWO;一轮显示完后判开关

TAB3:DB 3FH,06H,5BH,4FH,66H,6DH,7DH,07H 7FH,6FH,40H,7CH,5EH;0.1.2.3.4.5.6.7.8.9.-.b.d,的字形表“bd”在显示生日时间时显示在LED56;**************************************************SEVEN生日时显示生日祝福语“HAPPY” SEVEN:MOV P1,#01H MOV P2,#76H DJNZ R0,SEVEN SEVEN1:MOV P1,#02H MOV P2,#77H DJNZ R0,SEVEN1 SEVEN2:MOV P1,#04H MOV P2,#73H DJNZ R0,SEVEN2 SEVEN3:MOV P1,#08H MOV P2,#73H DJNZ R0,SEVEN3 SEVEN4:MOV P1,#10H MOV P2,#6EH DJNZ R0,SEVEN4 LJMP TWO;一轮显示完后判开关

;******************************************************************EIGHT判断是否闹铃子程序 EIGHT:MOV A,RE CJNE A,#0A1H,EIGHT1 MOV A,MIN CJNE A,RM,EIGHT1 MOV A,HOUR CJNE A,RH,EIGHT1 SJMP EIGHT4;闹铃时间到则CPLP1.6一次并忽略生日标志（即NB有效）EIGHT1:MOV A,MIN CJNE A,#59H,EIGHT7 MOV A,SECOND CJNE A,#59H,EIGHT5;是否等于59分59秒 EIGHT2:MOV A,COUNT;是否到达后半秒 CJNE A,#10,EIGHT3 EIGHT3:JC EIGHT7 EIGHT4:CPL P1.6 SETB NB SJMP EIGHT7 EIGHT5:MOV A,SECOND CJNE A,#51H,EIGHT6;是否大于51秒 EIGHT6:JC EIGHT7 JNB 10H,EIGHT7;判断是否报低音

JB FC,EIGHT7;只有FC有效时才输出

SJMP EIGHT2 EIGHT7:CPL FC;用来控制报低音和高音，满足报低音条件时，调用两次本程序对P1.6取反一次，高音时调用一次取反一次

RET;******** NINE中断（T0）计时程序（包含了秒－分－时－日－月－年间的进位及判断大小月，平闰年）

NINE:MOV TH0,#3CH;开定时器 MOV TL0,#0B0H SETB TR0 INC COUNT MOV A,COUNT CJNE A,#20,INEAA SJMP AAA INEAA:LJMP NINE1 AAA:MOV COUNT,#0;计时 MOV A,SECOND ADD A,#01 DA A;换成bcd码以方便显示 MOV SECOND,A CJNE A,#60H,INEAA MOV SECOND,#0 MOV A,MIN ADD A,#01 DA A MOV MIN,A CJNE A,#60H,INEAA MOV MIN,#0 MOV A,HOUR ADD A,#01 DA A MOV HOUR,A CJNE A,#24H,INEAA MOV HOUR,#0 MOV A,DAY ADD A,#01 DA A MOV DAY,A;************************判断平闰年及大小月 MOV A,MONTH CJNE A,#02H,TEN6A MOV A,YEAR;把年由BCD码换成二进制码 ANL A,#0F0H SWAP A MOV B,#10 MUL AB MOV 24H,A MOV A,YEAR ANL A,#0FH ADD A,24H JB ACC.0,TEN5A;二进制码后两位为00表示为闰年 JB ACC.1,TEN5A MOV 24H,#01 MOV A,DAY CJNE A,#30H,NINE1 MOV DAY,#1 SJMP NINE0 TEN5A:MOV A,DAY CJNE A,#29H,NINE1 MOV DAY,#1 SJMP NINE0;**************判断大小月；大于等于8月时双月为大月，小于8月时单月为大月 TEN6A:MOV A,MONTH CJNE A,#08H,TEN7A TEN7A:JC TEN9A JB 18H,TEN8A MOV A,DAY CJNE A,#32H,NINE1 MOV DAY,#1 SJMP NINE0 TEN8A:MOV A,DAY CJNE A,#31H,NINE1 MOV DAY,#1 SJMP NINE0 TEN9A:JNB 18H,TEN10A MOV A,DAY CJNE A,#32H,NINE1 MOV DAY,#1 SJMP NINE0 TEN10A:MOV A,DAY CJNE A,#31H,NINE1 MOV DAY,#1;******************* NINE0:MOV A,MONTH ADD A,#01 DA A MOV MONTH,A SETB 05H CJNE A,#13H,NINE1 MOV MONTH,#1 MOV A,YEAR ADD A,#01 DA A MOV YEAR,A NINE1:MOV A,MONTH CJNE A,BM,NINE2 MOV A,DAY CJNE A,BD,NINE2 JNB 05H,NINE2 SETB BS NINE2:RETI;*****************************************TEN中断（T1）预置加一程序由INT0控制其的开启与关闭

;*******************判断预置项目 TEN:MOV TH1,#3CH MOV TL1,#0B0H SETB TR1 INC COUNTS MOV A,COUNTS CJNE A,#15,TENE MOV COUNTS,#0 JB P0.0,RBRB JB P0.1,DAT SJMP TIME DAT: LJMP DATE RBRB:JB P0.1,BDAT LJMP RTIME BDAT:LJMP BDATE TENE:RETI;**********************预置时间 TIME: JNB P0.3,TEN1 MOV A,MIN ADD A,#01 DA A MOV MIN,A CJNE A,#60H,TENA MOV MIN,#0 SJMP TENA TEN1:JNB P0.2,TENA MOV A,HOUR ADD A,#01 DA A MOV HOUR,A CJNE A,#24H,TENA MOV HOUR,#0 TENA:RETI;******************预置日期 DATE:JNB P0.3,TEN3 MOV A,MONTH ADD A,#01 DA A MOV MONTH,A CJNE A,#13H,TENB MOV MONTH,#1 SJMP TENB TEN3:JNB P0.2,TEN4 MOV A,YEAR ADD A,#01 DA A MOV YEAR,A SJMP TENB TEN4:JNB P0.4,TENB MOV A,DAY ADD A,#01 DA A MOV DAY,A;***************判断平闰年 MOV A,MONTH CJNE A,#02H,TEN6 MOV A,YEAR ANL A,#0F0H SWAP A MOV B,#10 MUL AB MOV 24H,A MOV A,YEAR ANL A,#0FH ADD A,24H JB ACC.0,TEN5 JB ACC.1,TEN5 MOV A,DAY CJNE A,#30H,TENB MOV DAY,#1 SJMP TENB TEN5:MOV A,DAY CJNE A,#29H,TENB MOV DAY,#1 SJMP TENB;**************判断大小月 TEN6:CJNE A,#08H,TEN7 TEN7:JC TEN9 JB 18H,TEN8 MOV A,DAY CJNE A,#32H,TENB MOV DAY,#1 SJMP TENB TEN8:MOV A,DAY CJNE A,#31H,TENB MOV DAY,#1 SJMP TENB TEN9:JNB 18H,TEN10 MOV A,DAY CJNE A,#32H,TENB MOV DAY,#1 SJMP TENB TEN10:MOV A,DAY CJNE A,#31H,TENB MOV DAY,#1 TENB: RETI;**************************预置闹铃时间 RTIME:JNB P0.3,TEN12 MOV A,RM ADD A,#01 DA A MOV RM,A CJNE A,#60H,TENC MOV RM,#0 SJMP TENC TEN12:JNB P0.2,TENC MOV A,RH ADD A,#01 DA A MOV RH,A CJNE A,#24H,TENC MOV RH,#0 TENC:RETI;************************预置生日日期 BDATE:JNB P0.3,TEN14 MOV A,BD ADD A,#01 DA A MOV BD,A MOV A,BM CJNE A,#02H,TEN15 MOV A,BD CJNE A,#30H,TEND MOV BD,#1 SJMP TEND TEN15:CJNE A,#08H,TEN16 TEN16:JC TEN18 JB 18H,TEN17 MOV A,BD CJNE A,#32H,TEND MOV BD,#1 SJMP TEND TEN17:MOV A,BD CJNE A,#31H,TEND MOV BD,#1 SJMP TEND TEN18:JNB 18H,TEN19 MOV A,BD CJNE A,#32H,TEND MOV BD,#1 SJMP TEND TEN19:MOV A,BD CJNE A,#31H,TEND MOV BD,#1 SJMP TEND TEN14:JNB P0.2,TEND MOV A,BM ADD A,#01 DA A MOV BM,A CJNE A,#13H,TEND MOV BM,#1 TEND:SETB 05H RETI;*******************************ELEVEN中断（INT0）控制了预置的开关以及生日信号的清除

ELEVEN:JNB SS,ELEVEN1;预置有效时按一次INT0关预置 CLR SS CLR TR1 SJMP ELEVEN3 ELEVEN1:JNB BS,ELEVEN2;预置无效判断生日信号有效则清除生日信号 CLR 05H CLR BS SJMP ELEVEN3 ELEVEN2:SETB SS;都无效则令预置有效 MOV TH1,#3CH MOV TL1,#0B0H SETB TR1 ELEVEN3:RETI;***************************************************************TWELVE 延时小程序

TWELVE:MOV P1,#0 MOV P2,#0 DJNZ R0,TWELVE TWELVE1:MOV P1,#0 MOV P2,#0 DJNZ R0,TWELVE1 RET